 |
| AAI Whirlpool System is customizable to include as few or as many jets as needed. |
|
|
 |
| Available in plastic matching trims, and many Solid Metal finishes (not coated plastic that will flake off) |
|
|
 |
| For very little extra why not go Whirly for a true whirlpool experience |
|
|
|
In the past, you have sold a jet that pounds the same area of your body, "NO MORE"! American's new Whirl-Jet revolves on stainless steel bearings, enclosed in a plastic housing assuring constant movement with no drag or friction. The difference is the massaging action to your body and so invigorating that a standard jet will no longer be satisfying.
The greatest part is the cost which is only a little higher than the old standard jets. Do not show the new Whirl-Jet to a customer unless you are ready to sell it!!
|
 |
| 6-Jet Mini Lateral Jet Fittings |
|
|
|
|
Above we are offering this Setup as a complete add on kit to our Whirlpool System kit for only an
Additional 24 Dollars.
What you will receive with the kit is 7 feet of PVC hose, the 1" x 1" x 6 Outlet PVC fitting,
6-Lateral Mini Jet wall fittings and 6-Lateral Mini Jets. This is easily installed when
plumbing the whirlpool system by simply inserting in between the 1" PVC water
line. This is a fantastic add on for extra massage features at any area needed.
Back Massage, Foot Massage, Thigh Massage etc.
Add 6 Mini Lateral Jets or More
Your only limited by your Imagination
|
 |
| Venturi 4-Way Jet Adapter |
|
| Here we have our Venturi 4-Way Jet Adapter. Simply insert at the end of your plumbing to allow for 4 more
Mini Lateral Jets to be added onto your whirlpool system. This is a great addition at the front
of the bathtub in order to add Stimulating Foot Jets at a very reasonable cost to your
customer. This kit includes the mini 4-Way adapter with two plugs allowing you to
build a two, three or four jet Foot Massage area, and 7 feet of PVC hose.
The cost for this set up is only
20 dollars give your
customer the
best
|
 |
| Large Adjustable Jet |
|
|
Whirlpool System Installation Guide
The Following are Several Basic Points to Consider
When Installing Your American Whirlpool System: |
1. Suction inlet on motor should be 1/4" higher than suction fitting on tub. This will eliminate air locks and insure proper drainage.
2. For whirlpool system to drain properly, install all jets sloping toward foot jets or side jets higher than front or back jets allowing the water in your lines to drain in both directions.
3. Jets should be placed a minimum of four(4) inches below safe water level.
4. Pump should be mounted at the rear of tub. (Opposite end from drain)
5. All cement joints should be clean and free of defects.
6. To insure maximum drainage of your whirlpool system always make sure all piping is pulled as tight as possible eliminating any and all sagging that could possibly hold water.
7. Before hand tightening all fittings make sure backside of tub is smooth and free of defects. Check to insure that all "O" rings are in correctly and silicone is applied liberally to avoid leaks. Hand tighten wall fittings only.
|
Any and all repairs should be made only
by authorized dealers and their authorized personnel.
If you need assistance or have any questions on the American whirlpool system
you may call any of the American representatives. |
|
Use and Care Guide for American Whirlpool System |
- Before initial operation of your new American System take a few minutes to read instructions on its operation.
- Never allow the whirlpool system to run without sufficient water in the tub. The pump is designed to be cooled by the water.
Continued operation without water could damage seal or impeller.
- Never allow small children in the bath tub without proper supervision.
- Don't place small articles in the bathtub that could possibly enter into the jets or suction area.
- If your system is operated by a timer or wall switch always set timer or switch while out of the bathtub.
- If your system is operated by an air switch it can be turned on or off at any time while in the bathtub.
- Make sure the eyeballs of all jets are turned in a downward position.
- Do not add bubble bath, soaps or oils to the water.
- While in the bathtub you may start making the necessary adjustments for the most comforting and relaxing bathing experience:
a. Adjust the eyeballs for the directional flow that most suits you.
b. By adjusting the Air Control(s) you can determine your own air and water mixture. The Air Control closed all the way will eliminate air from your jets. Open your control(s) a slight turn at a time until the suitable massage action is determined.
- Be careful not to overdo your stay in the bathtub.
|
Cleaning Tips for American Whirlpool Systems |
It is necessary to regularly clean your American Whirlpool System, especially when taking oil baths. Normal cleaning should be about once a month.
a. Fill your bathtub with warm water.
b. Add 1 cup of Clean Way or call for other recommended products.
c. Turn your system on and allow it to run for about 10 minutes.
d. Drain bathtub.
e. Fill your tub once again with rinse water and allow your system to run another 10 minutes purging all soap from the lines.
f. Drain tub - and you should now have a clean and sanitary whirlpool system. |
|
| Trouble Shooting Guide |
| Pump Won't Start |
Check wiring to motor
Check to make sure on/off switch or pneumatic switch is on.
Check to see that airline from air switch to motor is connected.
Check circuit breaker. |
| Motor Hums |
Check for obstructions in pump.
Check to see if shaft is turning.
Check to see if impeller in pump is turning.
|
| Motor Shuts On/Off |
Motor is equipped with an overload protector. If proper wire gauge has not been used, the line voltage to your motor will not be sufficient to carry your motor load without over heating.
Check to insure correct circuit breaker has been installed.
|
| System Leaks |
Check all pipe joints on whirlpool system.
Check "O" rings in pump unions to see if rings are properly seated.
Check pump seals.
|
| Water at Air Control |
Check all venturis. Air lines on top and water lines at the bottom.
Check all lines to insure no lines have been crossed during installation.
Check to insure no glue during installation has obstructed the air or water orifices.
|
| Pump Won't Prime |
motor is designed for flooded suction use. Pump should be slightly higher than bathtub suction.
Check highest jets for any possible obstructions.
Check for any leaks in whirlpool system.
Check for obstruction in the pump.
Check for air leaks in the suction line and loosen union to see if "O" ring is seated properly.
Water level should be above highest jet.
|
Limited Lifetime Warranty
WARRANTY:
To all original purchasers of its products, American Acrylic & Injection, Inc., 419 Welch Dr., Farmersville, TX 75442, Warrants its motors free from defects in material and workmanship for a period of five years and limited life time warranty on the pump and whirlpool components.
Products which fail or become defective during the warranty period, except as result of freezing, accident, negligence, improper installation, use, or card, shall be repaired or replaced at our option, without charge within 90 days of receipt of defective product, barring unforeseen delays.
American Acrylic & Injection, Inc. shall not be responsible for cartage, removal and/or reinstallation labor, or any other such costs incurred in obtaining warranty replacements.
Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Pump:
American Acrylic & Injection, Inc. is not responsible for loss of the system or inconvenience, loss or damage to personal property or their consequential damage.
American Acrylic & Injection, Inc. extends a limited lifetime warranty to all original purchasers of its pumps that they are free from defects in materials and workmanship. Note: Alteration of pump location voids warranty.
The limited lifetime warranty applies only on the plastic pump parts as manufactured my American Acrylic & Injection, Inc. and specifically excludes all components and/or parts which are accessories therein. The motor/air switch is warranted for a period of five (5) years by the manufacturer to the original purchaser from the date of purchase.
Products which fail or become defective during warranty period shall be repaired or replaced at our option without charge and within 60 days of receipt of the defective product.
In case of removal or replacements, the purchaser assumes the responsibility for labor expenses for service, removal reinstallation, unless a service labor agreement exists between the purchaser and dealer.
The warranties made above are only warranties on the separate components of the system. Improper or negligent installation of your tub with the plumbing, electrical or hook-up connections, or alterations or modifications to the system are not covered by any warranty, express or implied. This is the only expressed or implied warranty given by American Acrylic & Injection, Inc.
To obtain warranty replacements or repair, defective products should be returned, transportation paid, to the place of purchase, or to American Acrylic & Injection, Inc.
|
 |
| Safety 1st with the AAI Safety Suction Valve |
|
|
 |
| Safety Suction Valve Configuration |
|
|
|
Safety is the Problem and duty to your Customers
American Has the Solution
AAI has been working on ways to guarantee the safety of the public for many years, regardless of who manufactured the product. We have designed this SAFETY SUCTION VALVE with the general safety of the public in mind. This valve is installed in the suction line by a 1 1/2" x 1 1/2" x 1" tee stubbed above the overflow. The valve is adjustable to any psi desired to meet all safety standards. The valve should eliminate practically all concerns connected with the hair entrapment issue. American Acrylic & Injection Inc. feels that if a maximum of 2 psi is reached on the suction before the valve de- primes the pump, the unit should be safe.
If the pressure on the cover should reach 2 psi the pump with immediately shut down and release the object covering the suction valve. Once the object has been removed and the pump has had an opportunity to re-prime itself, it will begin operating again. We feel the strongest feature of this valve is its construction. With no parts to wear out or malfunction our simple spring loaded construction should practically assure the unit's working order.
Free Sample
American Acrylic & Injection Inc. has reason to believe that our safety suction valve will become an ANSI/IAPMO standard in the near future. Therefore we are proud to offer whirlpool bathtub manufacturers a Free Sample for observation and testing. If you are a distributor of bathtub, spa, or swimming related products and would like further information, please call AAI
Since this safety suction valve is related to the health and safety of our customers, we fell that all whirlpooled bathtubs should be equipped with one. Priced at $6.50 each, it is a small price to ensure complete safety for your customers and protection for yourself against lawsuits. We must consider what would happen to the shrill bathtub industry if one of the national news networks should break a story that whirlpool tubs could possible harm your child. Make sure you are completely safe NOW before this happens.
By Special arrangement the valve can carry your logo. By calling 1 800-666-7961 you can receive your Free Sample to test in your own plant. Call Today so that you can rest easier knowing the products you sell are completely safe from hair entrapment!
|
 |
| AMERICAN AIR MASSAGE 16-JET SYSTEM |
|
|
 |
| AMERICAN AIR MASSAGE |
|
|
|
